board_rzusb.h File Reference

Atmel Raven Development Kit, USB Stick, AT86RF230 Radio Adapter with Atmega1287. More...

Go to the source code of this file.

Defines
#define	HIF_TYPE   (HIF_AT90USB)
#define	HWTIMER_REG   (TCNT1)
#define	HWTIMER_TICK   ((1.0*HWTMR_PRESCALE)/F_CPU)
#define	HWTIMER_TICK_NB   (0xFFFFUL)
#define	HWTMR_PRESCALE   (1)
#define	LED_ACTIVITY   (0)
#define	LED_CLR(x)
#define	LED_GET_VALUE()
#define	LED_INIT()
#define	LED_NUMBER   (3)
#define	LED_SET(x)
#define	LED_SET_VALUE(x)
#define	LED_TOGGLE(ln)
#define	LED_USB_CONFIGURED   (3)
#define	LED_VAL(msk, val)   do{}while(0)
#define	NO_KEYS
#define	TIMER_INIT()
#define	TIMER_IRQ_vect   TIMER1_OVF_vect
#define	TIMER_POOL_SIZE   (4)
#define	TIMER_TICK   (HWTIMER_TICK_NB * HWTIMER_TICK)
#define	USB_BCD_RELEASE   URACOLI_USB_BCD_RELEASE
#define	USB_PID   URACOLI_USB_PID
#define	USB_PRODUCT_NAME   URACOLI_USB_PRODUCT_NAME
#define	USB_VENDOR_NAME   URACOLI_USB_VENDOR_NAME
#define	USB_VID   URACOLI_USB_VID

---

Detailed Description

Atmel Raven Development Kit, USB Stick, AT86RF230 Radio Adapter with Atmega1287.

This board wiring fits the Atmel radio development kit hardware.

The wiring of the radio and the AT90USB1287 is shown below:

     AVR            RF230
     ---            -----
     PB4      -->  SLPTR
     PD6/T1   <--  MCLK
     PD4/ICP1 <--  IRQ
     PB5      -->  RSTN
     PB0      -->  SEL
     PB2      -->  MOSI
     PB3      <--  MISO
     PB1      -->  SCLK
     PB7      -->  TST

     Schematic   AVR  Index
     ---------   ---  -----
     LED2:       PD5  (#0) red
     LED3:       PE7  (#1) green
     LED4:       PE6  (#2) yellow
     LED1:       PD7  (#3) blue (VBUS, USB supply)

Fuses/Locks?????:
     LF: 0xe2 - 8MHz internal RC Osc.
     HF: 0x11 - without boot loader
     HF: 0x10 - with boot loader
     EF: 0xff
     LOCK: 0xef - protection of boot section

Original Fuses/Locks
     LF: 0xde
     HF: 0x91
     EF: 0xfb
     LOCK: 0xff

Bootloader:
    Start at byte=0x1e000, address=0xf000, size = 4096 instructions/ 8192 bytes

Build Options

• rzusb : Raven USB Stick

---

Define Documentation

#define LED_CLR

(

x

)

Value:

switch (x) { \
  case 3: PORTD &= ~_BV(7); break; \
  case 0: PORTD |= _BV(5); break; \
  case 1: PORTE |= _BV(7); break; \
  case 2: PORTE |= _BV(6); break; \
  }

#define LED_GET_VALUE

(

)

Value:

( \
  ((PORTD & _BV(5))? 0: 1) | \
  ((PORTE & _BV(7))? 0: 2) | \
  ((PORTE & _BV(6))? 0: 4) \
              )

#define LED_INIT

(

)

Value:

do { \
  DDRD |= _BV(7) | _BV(5); DDRE |= _BV(7) | _BV(6); \
  PORTD &= ~_BV(7); PORTD |= _BV(5); PORTE |= _BV(7) | _BV(6); \
  } while (0)

#define LED_SET

(

x

)

Value:

switch (x) { \
  case 3: PORTD |= _BV(7); break; \
  case 0: PORTD &= ~_BV(5); break; \
  case 1: PORTE &= ~_BV(7); break; \
  case 2: PORTE &= ~_BV(6); break; \
  }

#define LED_SET_VALUE

(

x

)

Value:

do { \
  if (x & 1) PORTD &= ~_BV(5); else PORTD |= _BV(5); \
  if (x & 2) PORTE &= ~_BV(7); else PORTE |= _BV(7); \
  if (x & 4) PORTE &= ~_BV(6); else PORTE |= _BV(6); \
  } while (0)

#define LED_TOGGLE

(

ln

)

Value:

switch (ln) { \
  case 3: PORTD ^= _BV(7); break; \
  case 0: PORTD ^= _BV(5); break; \
  case 1: PORTE ^= _BV(7); break; \
  case 2: PORTE ^= _BV(6); break; \
  }

#define LED_VAL	(		msk,
			val
	)			do{}while(0)

#define TIMER_INIT

(

)

Value:

do{ \
        TCCR1B |= (_BV(CS10)); \
        TIMSK1 |= _BV(TOIE1); \
    }while(0)